Bursa, Türkiye – 16 November 2026. An orbital stretch wrapper moves the product through a rotating ring and wraps each piece or bundle on all four long sides. A turntable stretch wrapper rotates a whole pallet and wraps the load from the outside. If you ship long, flat or surface-sensitive products such as profiles, doors, panels or furniture parts, an orbital (horizontal) wrapper is usually the right machine; if you ship stacked cartons or bags on standard pallets, a turntable is. Many plants use both.
How a turntable stretch wrapper works
The pallet is placed on a rotating table, usually with a forklift. As the table turns, a film carriage travels up and down a mast and applies film in a spiral from the bottom of the load to the top and back. On the Wraptor 1500 VPT 2700, for example, the table is Ø1500 mm, takes pallets up to 1200 × 1000 mm and 1500 kg, and wraps up to 2700 mm high. Its motorised pre-stretch carriage stretches the film by up to 250%, so one metre of film on the roll covers up to 3.5 metres of the load.
The wrap holds the load together as one unit. It does not wrap the individual items inside, and it does not cover the top of the load unless a top sheet is added.
How an orbital stretch wrapper works
The product lies on a belt conveyor and travels through a ring. A film carriage on the ring rotates around the product and lays a continuous spiral of stretch film over all four long sides. Because the product keeps moving, there is no length limit: the same Spinner 1000 S wraps a 600 mm frame part and a 2.4 m door leaf. What limits the machine is the cross-section that fits through the ring – and because the ring is round, a product can be wider if it is lower.
Overlap, meaning how much each turn covers the previous one, comes from the relation between conveyor speed and ring speed. Both are adjustable on the operator panel: a slower conveyor or a faster ring gives a stronger pack, a faster conveyor saves film.
Orbital vs turntable: side-by-side comparison
| Orbital (horizontal) wrapper | Turntable (vertical) wrapper | |
|---|---|---|
| What is wrapped | Each product or bundle | The whole pallet load |
| Typical products | Profiles, pipes, doors, panels, furniture parts | Cartons, bags, mixed pallets |
| Product length | Unlimited | Limited by the pallet, e.g. 1200 × 1000 mm on a Ø1500 mm table |
| Surface protection | All four long sides covered; parts do not rub against each other | Outer faces of the load only |
| Position in the plant | Inline, after cutting, extrusion, edge banding or painting | End of line or warehouse, after palletising |
| Loading | Conveyor, by hand or straight from the line | Forklift or pallet truck |
| Film | Narrow rolls: 170 mm (Spinner 600 S, 1000 S) up to 500 mm (Spinner 2200 S) | 500 mm rolls, pre-stretch up to 250% (Wraptor VPT) |
| Power | Three-phase, e.g. 380 V and 2.3 kW total (Spinner 1000 S) | Single-phase 220 V, 1 kW (Wraptor 1500 VPT 2700) |
When a turntable is the wrong machine
When long products are stacked on a pallet and wrapped on a turntable, the film only holds the outside of the stack. Profiles or panels inside can still slide and rub, and loads longer than the pallet hang over the table. Once the pallet is broken down at a distributor or on a building site, each piece is unprotected – and that is where long products are most often damaged. Doors, cabinet fronts and finished profiles also need protection from dust and fingerprints from the moment they leave the line, before they are stacked at all.
When an orbital wrapper is the wrong machine
Mixed cartons on standard pallets do not need each carton wrapped. A turntable pallet wrapper unitises the whole load in one cycle and is the simpler machine. For oversized or very heavy loads that cannot go on a turntable, a self-propelled pallet wrapping robot such as the Robowrap drives around the load instead.
Sizing an orbital wrapper to your cross-section
All Spinner S machines work on the same principle; the ring size decides what you can wrap. The two values per model are the corners of the round ring capacity.
| Model | Max. cross-section (W × H) | Film width | Conveyor |
|---|---|---|---|
| Speedwrap 550 | 260 × 270 mm | 170 mm | up to 36 m/min |
| Spinner 600 S | 477 × 300 / 545 × 243 mm | 170 mm | 15 m/min |
| Spinner 1000 S | 700 × 450 / 950 × 185 mm | 170 mm | 12 m/min |
| Spinner 1500 S | 950 × 800 / 1350 × 500 mm | 250 mm | 10 m/min |
| Spinner 1800 S | 550 × 1300 / 1500 × 950 mm | 250 mm | 12 m/min |
| Spinner 2200 S | 1600 × 1100 / 2000 × 800 mm | 500 mm | Customised |
Size the machine for the largest product you ship regularly, not the average one. The “Does it fit?” calculator on each Spinner page checks any width and height against the ring. For the other questions to answer before choosing a model, see our orbital wrapping machine buying guide.
Can an orbital wrapper wrap pallets?
Yes, when the load travels lengthwise on a conveyor. The Spinner 2200 S Pallet is a fully automatic end-of-line system that wraps pallets and board stacks from 700 × 400 × 2000 mm with 500 mm film, passing the film under the load as well as over it. See the end-of-line case study for a heavy-duty installation.
When you need both
In furniture, door and profile plants it is common to run both: an orbital wrapper at the line protects each piece or bundle, and a turntable at dispatch unitises boxed goods, spare parts and mixed orders.
Frequently asked questions
Can a turntable wrapper wrap long profiles?
Only as a palletised stack, and only if the stack fits the table. The profiles inside are not individually protected. For profiles longer than a pallet, or for surfaces that must stay clean, use an orbital wrapper.
Is an orbital wrapper the same as a horizontal stretch wrapper?
Yes. Both names describe a machine where the product travels horizontally through a rotating ring.
Which one uses less film?
It depends on the product. On an orbital wrapper the overlap is set per product, so light parts are not wrapped with the heaviest setting. On a turntable, pre-stretch of up to 250% stretches each metre of film to up to 3.5 metres.
What power supply do they need?
The Spinner 1000 S runs on 380 V three-phase power (2.3 kW total). The Wraptor 1500 VPT 2700 runs on 220 V single-phase power (1 kW).
How do I know which Spinner fits my products?
Enter your product’s width and height in the “Does it fit?” calculator on the Spinner pages, or send us your dimensions.
Tell us what you wrap, its dimensions and the output you need – our engineers will recommend the right machine. Write to info@eddapack.com or use our contact form.
