Bursa, Türkiye – 19 November 2026. The safest way to pack aluminium profiles is to wrap them in stretch film straight after the saw, before they are stacked, bundled or handled. Single profiles are wrapped inline at extrusion speed; wider bundles go through a larger orbital ring; shrink film with banding is an option for tight bundles. Which one fits depends on your cross-sections, line speed and whether you ship single profiles or bundles.
Why aluminium profiles get damaged
Anodised, powder-coated and mill-finish surfaces mark easily, and most damage happens after the press, not in the truck. Profiles rub against each other in racks and bundles, pick up handling marks and dust, and moisture trapped between bare profiles can stain the surface. Damage often shows only when the customer opens the bundle, which makes it expensive: the whole length is rejected, not just the marked spot.
Wrapping each profile, or each bundle, in a tight spiral of stretch film keeps the surface covered on all sides from the moment it leaves the line.
Three ways to pack aluminium profiles
| Method | Best for | Edda solution | Key figures |
|---|---|---|---|
| Single profiles wrapped inline | High-volume extrusion and cutting lines | Speedwrap 550 (stand-alone) or Speedwrap Profiline (complete line) | Up to 36 m/min; cross-section up to 260 × 270 mm; from 70 × 18 × 1000 mm |
| Bundles wrapped orbitally | Wider bundles, mixed profile families | Spinner 1000 S | Up to 700 × 450 / 950 × 185 mm; unlimited length |
| Shrink film bundles with banding | Tight, uniform bundles of profiles or pipes | Shrink Nylon Lines | 70 µm PE shrink film; up to 30 m/min; up to 250 × 250 mm; bundles up to 6000 mm |
For heavy profiles and steel tubes, Heavy Duty Lines use the same orbital principle with a stronger conveyor and ring.
Inline wrapping at extrusion speed
Extrusion lines run continuously, and packing must not slow them down. The Speedwrap 550 combines a conveyor running at up to 36 m/min – three times the speed of a standard Spinner – with a ring turning at up to 140 rpm, so profiles are wrapped as fast as they leave the saw. The Speedwrap Profiline builds this into a complete line: infeed transfer tables, a belt conveyor, a wrapping unit with two stretch film cartridges and outfeed tables, for profiles up to 6000 mm long.
Wrapping bundles
When profiles leave the line in groups, wrapping the bundle holds the profiles together and stops them rubbing against each other inside it. The Spinner 1000 S takes bundles up to 950 mm wide at heights up to about 185 mm, or 700 mm wide at heights up to 450 mm, with no length limit. If most of your bundles fit but a few are wider, size the machine for the largest bundle you ship regularly.
Choosing the stretch film
Edda’s profile wrappers take 170 mm wide film on a 76 mm core, in 23, 30 or 35 micron.
- 23 micron: dust and scratch protection for light profiles that travel in boxes or on racks.
- 30 micron: a common all-round choice for profiles and profile bundles.
- 35 micron: heavier bundles, sharp-edged profiles, long distances or outdoor storage.
Film use depends mainly on overlap, which is set by conveyor speed and ring speed. Because both are adjustable per product, light profiles do not have to be wrapped with the heaviest setting.
Planning the line after the saw
Before asking for a quote, collect these five points – they decide the machine and the layout:
- Profile range: cross-sections and lengths.
- Line speed and profiles per minute.
- Single profiles or bundles.
- How the wrapper connects to the extrusion or cutting line.
- Floor length available for infeed and outfeed tables.
Edda designs the conveyors, transfers and buffer zones around the wrapper, so the line fits the space you have. See our PVC and aluminium profile packaging solutions for complete line examples.
Manual or automatic?
Hand wrapping is slow, uses more film than needed and gives a different result with every operator. Automatic wrapping gives the same overlap and tension on every profile and frees people for other work: in one PVC profile installation, an automatic line reduced packing staff from 10 people to 3.
Frequently asked questions
Which machine wraps aluminium profiles at extrusion speed?
The Speedwrap 550 wraps profiles up to 260 × 270 mm at up to 36 m/min. As a complete line with infeed and outfeed tables, it is the Speedwrap Profiline.
Can bundles be wrapped instead of single profiles?
Yes. Compact bundles fit the Speedwrap 550; wider bundles up to 950 mm go through the Spinner 1000 S.
What is the longest profile that can be wrapped?
Orbital wrappers have no length limit. The Speedwrap Profiline line is designed for profiles up to 6000 mm.
Which film thickness should I use?
30 micron suits most profiles and bundles; 23 micron for light parts, 35 micron for heavy or sharp-edged bundles and long transport.
Is this the same machine as for PVC profiles?
The same wrappers handle PVC and aluminium. For PVC profiles, bundles on wooden supports and window frames, see our guide to PVC profile wrapping machines.
Send us your profile cross-sections, lengths and line speed – we will recommend a wrapper or a complete line. Write to info@eddapack.com or use our contact form.
